Waterproof layer
Felt, synthetic or self-adhered underlayment is installed before any tile goes on the roof.
Tile Roofing
Tile Roof Installation Rockaway, NJ
A Rockaway tile roofer can help choose between clay and concrete, flat or curved profiles, and install the full system beneath the tile. Dial (862) 421-0113 to talk with a local roofer about a new tile roof.
Tile is one of the heaviest roofing materials a house can carry, so a tile roof installation starts below the roof. A tile roof weighs several times as much as asphalt shingles, and a home built for shingles may need an engineer to check the rafters or trusses before switching. On new construction, the framing is sized for tile from the plans onward.
Next comes the material. Clay tile is fired, keeps its color for a very long time and is lighter than most concrete tile, while concrete tile comes in many profiles and slowly fades as its surface weathers. Profiles run from flat tiles that look like slate or shakes to S-shaped tile and two-piece barrel tile.
The tile may last generations, but the layers below it decide when the roof leaks. Most tile needs a slope of at least 2.5 in 12, and building codes call for a doubled underlayment on slopes below 4 in 12. Choosing a long lasting underlayment now is what keeps the roof from needing a relay in twenty years.
If the problem goes deeper than it first looked, a Rockaway roofer may also recommend tile roof replacement or roof installation.
Looking for Rockaway tile roof installation? Call (862) 421-0113 to talk to a local roofer.
Call nowThe process
How tile roof installation works
Here is how a roofer usually installs a tile roof.
Confirm the framing
Before ordering tile, the load on the rafters or trusses is checked, reinforcement is planned if needed and the permit is filed. It is smart to keep a stack of spare tile from the same batch for future repairs.
Lay the underlayment
Decking is checked and fastened, drip edge goes on, and the deck is covered with the chosen underlayment, with self-adhered membrane in valleys and at eaves where ice or wind-driven rain is a concern. Since this layer does the waterproofing, it is where quality matters most.
Set the battens
Battens are fastened across the roof at spacing set by the tile, and on many roofs counter battens run beneath them so water can drain freely. The gap under the tile also helps heat escape before it reaches the deck.
Install flashing
Flashing goes in at valleys, sidewalls, headwalls, skylights and pipes, sized for the deep profile of tile. Because tile is thick and curved, flashing must be wider and shaped to fit.
Set the field tile
Tile goes on from the eave up, with an eave closure to keep birds out and fasteners or foam adhesive chosen for local wind requirements. Cut edges at valleys and hips are fitted and secured carefully.
Seal the top
Ridge and hip caps are set on a raised ridge board, either in mortar or with a dry ridge system and a vented closure that lets attic air out. Any tile cracked during the job is replaced before cleanup.
What is included
What tile roof installation includes
Tile attachment
Battens or direct fastening hold every course so tiles stay put in strong wind.
Valley metal
Wide valley metal and shaped wall flashings are installed which is where tile roofs usually leak.
Ridge finish
Eave and ridge details are finished with ventilation where the design calls for it.
Structural review
An engineer or span check confirms the structure especially when replacing shingles.
Related service
Barrel Tile Roof Installation Rockaway, NJ
Barrel tile is the classic two-piece tile roof: half-round pan tiles laid concave side up, with cover tiles laid over the joints between them. Their tapered shape and deep profile create the rolling texture that defines the style. The open curves at the eaves and ridges must be closed so birds, wind and rain cannot get in.
On a Rockaway barrel tile roof, the cover tiles are the ones wind targets, so how they are fastened matters most. A crew snaps lines so pans and covers stay straight from eave to ridge.
Related service
Spanish Tile Roof Installation Rockaway, NJ
Spanish tile, also called S tile, merges the curved pan and cover into one interlocking piece. It comes in clay and in concrete, with colors from terracotta to multi-tone blends. Side interlocks help it shed water, though the curved ends need bird stops and ridge closures just like barrel tile.
Spanish tile roof installation in Rockaway follows the same system as any tile roof, from structure check to underlayment, flashing and tile. Flashing around chimneys, walls and skylights has to be shaped to the S curve, often with formed metal or a flexible flashing material. With a color blend, tile is drawn from several pallets as it goes up so no area looks patchy.
Local help
Tile Roof Installation Near Me
In Rockaway, new tile roofs go onto homes of every age, from fresh builds to older houses moving away from shingles. In Rockaway and neighboring communities including Dover, Wharton, Mountain Lakes and Morris Plains, the biggest variable on a conversion is whether the existing framing can carry tile, and storms that bring strong wind make fastening choices as important as the tile itself.
Searching for tile roof installation near me from Rockaway or Dover, Wharton, Mountain Lakes and Morris Plains? Call (862) 421-0113 to talk to a roofer who works in your part of town.
How the weather here affects roofs around Rockaway
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, which is how ice dams form and back water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. Most homeowners in Rockaway, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why act early
Smaller repairs
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Familiar with local homes
Roofers in Rockaway know the roof types and weather wear common in local homes.
Know what happens next
Ask your questions before you agree to anything.
Tile Roof Installation questions
What underlayment goes under a tile roof?
Options include heavy felt, synthetic sheets and peel-and-stick membranes, often doubled on lower slopes. Since the tile can outlast the underlayment by decades, a longer lasting underlayment pays off. Codes call for two layers on slopes from 2.5 in 12 up to 4 in 12.
How heavy is a tile roof?
Tile weighs several times as much as asphalt shingles, with concrete tile usually the heaviest. Whether a given house can carry it depends on the framing, which is why conversions from shingles start with a structural review. Some lighter weight tile products are made for homes with less structural capacity.
Can tile be installed over an existing roof?
The old roofing is torn off before tile is installed. Tear-off exposes the decking so rotted boards can be replaced and the new underlayment can lap correctly.
How long does it take to put on a tile roof?
Expect more time than a shingle job, since each tile is placed and fastened by hand over more layers. Complex rooflines and framing work before tiling can stretch the schedule. Once the underlayment is down, the house is protected from rain while tile goes on.
What is better, clay or concrete tile?
Both make durable roofs with different tradeoffs. Clay keeps its color through the tile, is lighter than most concrete tile and can last for generations. Concrete tile comes in many profiles and finishes, but it is heavier, absorbs more water and its color fades over time.
More questions? Call (862) 421-0113
Related services
Tile Roof Replacement
Tile roof replacement that strips the roof to the deck, renews the underlayment and flashing and puts sound tile back on, so the layers under the tile last as long as the tile.
Learn moreRoof Installation
Installing a new roof layer by layer, from drip edge and underlayment to flashing, vents and the finished roofing, so it sheds water at every edge and seam.
Learn moreTile Roof Inspection
A close look at the tile, underlayment, flashing, valleys and attic of a clay or concrete tile roof, before buying a home, after a storm or as the underlayment ages.
Learn moreRoof Ventilation
Fixing hot, damp or poorly vented attics with the right mix of intake and exhaust, without mixing vent types that work against each other.
Learn more
Looking for something else?
See all roofing servicesTalk to a Rockaway roofer about tile roof installation
Call now for Rockaway tile roof installation and help in the towns around it.